Forward Converter Circuit Design and Analysis

October 14, 2019 Cadence PCB Solutions

Variable power supply

Designing a power supply or regulator for your PCB? You might consider using a forward converter for regulation.

 

Among the many power regulation methods used in PCBs, switched mode power supplies are useful as they can be configured to be robust against strong ripple. A typical buck-boost switching converter can send switching noise to downstream circuits through the output leads, which has been shown to cause inadvertent switching in digital circuits at high output currents. 

If you need low noise DC output from a power supply without having to worry about strong switching noise, a forward converter is a good alternative for moderate power output applications.

Flyback Converter vs. Forward Converter

Interestingly, the term “forward converter” is sometimes used to refer to a flyback converter, but this is not correct. A forward converter is designed with a similar topology, and both are switched mode converters that use a transformer between the input and output stages for galvanic isolation. Both converters can be designed to run in buck or boost mode. However, a forward converter solves a particular problem of transformer core saturation that occurs in a flyback converter.

In a real transformer, the magnetization in the transformer core needs to switch direction at the same rate as the input voltage/current in order to induce a current in the secondary coil. When the primary current is too large, the magnetic field causes the core to saturate, and magnetic hysteresis will distort the signal that is induced in the secondary coil. This means that the current in the primary coil in a real transformer must be less than the saturation current. This limits the current that can be reliably used in a flyback converter.

A forward converter solves this problem by using a diode and a three-winding transformer. The tertiary winding on the transformer and the diode are used to force the transformer to reset. Compared to a flyback converter, a forward converter has higher cost, faster transient response time, higher power efficiency, and lower ripple on the output. 

The lower output ripple and galvanic isolation between the input and output stages ensures there is less conducted EMI between stages and in the output. When one also considers solving the saturation problem that occurs in a flyback converter, a forward converter is suitable for regulation up to hundreds of Watts.

The circuit diagrams below show a typical flyback converter and forward converter. Note the polarity of the transformers on the input and output sides; the primary and secondary windings transformer have the same winding direction in order to ensure the currents have the same polarity, and a ratio of N:1 (primary:secondary) is normally used to analyze this circuit. The PWM signal is applied to the gate on Q1.

 

Flyback converter circuit diagram

 

 

Forward converter circuit diagram

 

Regulation with PWM in a Forward Converter

Regulation in a forward converter is achieved by applying a PWM signal to the gate of a transistor (normally a MOSFET) on the input side of the converter. The topology is similar to that in a flyback converter, although there is an additional diode and inductor on the output side, as well as the use of a three-winding transformer versus a two-winding transformer. Compared to a bust-boost switching regulator, a forward converter takes advantage of a transformer for galvanic isolation to suppress conducted EMI from propagating to the output side of the converter.

The inductor on the output side, the duty cycle of the PWM signal, and the switching frequency are the primary factors that determine the level of regulation enforced on the output current. The duty cycle is normally set to less than 50% if the number of turns on the primary coil equals that on the tertiary coil. Very simply, using a higher frequency PWM signal and larger output inductor will reduce the peak-to-peak fluctuation on the output current, which appears as a triangle wave. The ripple on the output current and its defining equation are shown in the graph below. Note that N is the turns ratio shown in the above forward converter circuit diagram.

 

Output current and voltage from a forward converter

Output current fluctuations from a forward converter

 

Simulating a Forward Converter

The primary simulations involved in analyzing a forward converter are time-domain simulations with a PWM signal. You’ll need to construct a PWM waveform and connect this to the gate on the MOSFET in your forward converter. You’ll also need to construct an input voltage with a superimposed ripple waveform if you want to compare the input and output peak-to-peak voltage/current fluctuations. Using a DC sweep allows you to examine power conversion efficiency and determine when the output starts to behave like a highly nonlinear circuit.

Transient analysis is also critical for examining the effectiveness of your PWM frequency you use. The transient response time will be a limiting factor that determines the switching frequency you can use. Normally, you would reduce the transient response time (equal to the RC time constant from the capacitor and load resistance) by using a smaller capacitor across the output, but this causes greater ripple to be seen on the output. One option is to use a lower PWM frequency and add filtration on the output to suppress residual switching noise and PWM ripple.

You can reach even higher power efficiencies with similar performance in other areas by using an active-clamp forward converter. This design only requires a two-winding transformers, but it forces transformer reset with multiple FETs on the input and output sides of the converter. A circuit diagram for this converter is shown below.

 

Active-clamp forward converter

Circuit diagram for an active-clamp forward converter

 

Power conditioning circuits require careful design and analysis prior to layout on a PCB, and you can easily import your design data in SPICE simulations using the OrCAD PSpice Simulator from Cadence. You’ll then be able to connect your forward converter circuit to a downstream circuit, giving you a full view of the behavior of your system and its response to noise in complex PCB designs.

If you’re looking to learn more about the solutions Cadence has for you, talk to us and our team of experts.

About the Author

Cadence PCB solutions is a complete front to back design tool to enable fast and efficient product creation. Cadence enables users accurately shorten design cycles to hand off to manufacturing through modern, IPC-2581 industry standard.

Follow on Linkedin Visit Website More Content by Cadence PCB Solutions
Previous Article
Testability Analysis Framework for Non-functional Requirements
Testability Analysis Framework for Non-functional Requirements

Testability analysis is an integral part of all design practices. The need to assess a product’s capabiliti...

Next Article
Understanding Link Budgets and Balancing SNR Ratios
Understanding Link Budgets and Balancing SNR Ratios

Your link budget indicates gain and losses throughout a system, but noise and other factors may affect the ...