CMOS Differential Amplifier Uses and Layout in Your PCB

October 15, 2019 Cadence PCB Solutions

CMOS differential amplifier ICs

Operational amplifier circuits on white background


Hearken back to your introductory electronics class, and you probably built plenty of circuits that used an operational amplifier like those shown in the above image. These circuits are fundamental when working with analog signals, as well as for manipulating and generating a number of waveforms.

If you’re using an SoC to build a new device for a particular application, then you likely won’t need to build your own amplifier circuits; these amplifiers will be integrated into the SoC and you can be rest assured that your signals will not be distorted as long as you layout your SoC correctly. Otherwise, you’ll need to layout a number of discrete components and properly route interconnects. This is where it helps to understand the difference between a CMOS differential amplifier and a single-ended amplifier.

Single-ended vs. Differential Amplifiers

As these names suggest, these different types of amplifiers use either single-ended or differential signalling. At the PCB level, any connections that you ground on a single-ended amplifier should be referenced to the same ground plane. The signal sent to the amplifier’s input should then be referenced to the same ground plane as the relevant connections on the amplifier. This is analogous to what is done in a standard logic gate IC or similar component.

With a differential amplifier, the input is generally an analog differential signal, meaning the voltage seen at each input has the same peak-to-peak voltage and opposite polarity. However, differential digital signals can also be used with a differential amplifier. The voltage seen by the amplifier is defined as the difference between the inverting and non-inverting inputs. This nicely provides common mode noise rejection.


Circuit symbols for amplifiers

Single-ended vs. differential amplifiers with single-ended output


Note that a differential amplifier can be used with single-ended signals by connecting one of the inputs to a desired potential (usually ground). In this case, the input single-ended signal you send to the amplifier input is referenced to the grounded input. Operational amplifiers are actually differential amplifiers that are typically run as equivalent single amplifiers in the manner described here. In order to provide amplification, a feedback loop is constructed between the output and one of the inputs; the exact level of amplification and the polarity of the output will depend on which inputs on the amplifier are used and the component values that appear in the feedback loop.

Note that differential amplifiers can have a differential output (called a fully-differential amplifier), which can also be converted to a single-ended output by grounding one of the terminals. In a fully-differential amplifier, the differential output can be used in multistage differential amplifiers (i.e., cascaded amplifier). Note that the common mode voltage output of some CMOS differential amplifiers can be controlled independently of the differential voltage output. In multistage amplifiers, the common mode output on upstream stages should be set to zero to prevent a downstream amplifier from entering saturation.

Coupling in a CMOS Differential Amplifier

If you are building a multistage CMOS differential amplifier from discrete components, then you’ll need to determine the best coupling method to use between amplifier stages. You’ll need to account for the amplifier’s bandwidth when determining the right coupling method for a multistage amplifier. As an example, RC coupling is normally used between amplifier stages as a high pass filter, effectively blocking any DC bias on the output from an upstream amplifier. LC coupling is also useful for radio signals, although be careful with the bandwidth of the LC filter you place between amplifier stages.

No matter which coupling method you use, you’ll need to ensure impedance matching when working with high speed or high frequency circuits. When working at high power and high frequency (i.e., in the Tx side of a microwave or mmWave signal chain), you’ll most likely need to impedance match each amplifier stage and length match your traces. Load-pull analysis is an ideal tool for determining impedance matching, and harmonic balance analysis is useful for examining distortion. When working with frequency modulated signals, you’ll need to use harmonic balance analysis to determine the third-order intermodulation products (3OIP) in your single-ended or differential amplifier circuit.

If you’re using an analog IC that is fabricated with a CMOS process, then it will likely include a CMOS differential amplifier stage. One great example is an integrated transceiver unit. The data input side of the unit might use differential signalling to receive data, which will be input to a CMOS differential amplifier. At the Rx and Tx sides, you’ll find a single-ended amplifier that runs near saturation and at the linear regime, respectively.


SoC with CMOS differential amplifier on white background

This CMOS SoC likely contains at least one CMOS differential amplifier.


If you’re using a CMOS amplifier for waveforming (i.e., converting an analog signal to a square wave by taking advantage of saturation at high input), then you’ll need to make sure that the output does not cross back into the analog section of the board. This type of waveshaping takes advantage of harmonic generation when an amplifier runs at saturation, which forces a periodic input analog signal to saturate the input and form a square wave. The higher order harmonic content can interfere with other sensitive analog signals in your board if the square wave output from your amplifier crosses back into the upstream analog section.

The great thing about a CMOS differential amplifier (and other amplifiers, for that matter) is that the inputs have high common-mode rejection ratio (CMRR); a decent amplifier will have CMRR that easily exceeds ~60 dB. Interference between different analog sections, or between analog and your new square wave will appear as common-mode noise elsewhere in the system. With a single-ended amplifier, you would have a noise feedback effect that raises the noise floor at the amplifier’s output. A differential amplifier will naturally filter this common mode noise, and you won’t have repeatedly amplified noise between different sections of the system.

When you need to include a CMOS differential amplifier in your circuits and examine their behavior, you need PCB design and analysis software that includes a full suite of layout and simulation. Allegro PCB Designer and Cadence’s full suite of analysis tools make it easy to perform important power and signal integrity simulations directly from your design data, offering a comprehensive view of the behavior of your circuits.

If you’re looking to learn more about how Cadence has the solution for you, talk to us and our team of experts.

About the Author

Cadence PCB solutions is a complete front to back design tool to enable fast and efficient product creation. Cadence enables users accurately shorten design cycles to hand off to manufacturing through modern, IPC-2581 industry standard.

Follow on Linkedin Visit Website More Content by Cadence PCB Solutions
Previous Article
What is RMS Noise and How Does it Compare to the Standard Deviation?
What is RMS Noise and How Does it Compare to the Standard Deviation?

The effects of RMS Noise on electronic circuits is an inevitable conclusion, but through design it can be m...

Next Video
Webinar: Conquer High-Speed Interfaces Faster
Webinar: Conquer High-Speed Interfaces Faster

New Tools to Manage Return Path and Crosstalk