How to Find a Short Circuit on a PCB

August 19, 2020 Cadence PCB Solutions

Key Takeaways

  • Learn the signs of a short circuit. 

  • Explore ways to find short circuits on a PCB.

  • Learn how to prevent short circuits during design. 

A fried chip on a printed circuit board

Short circuits can result in component failure

There are times where I’m completely scatterbrained. I can remember searching all over for my smartphone only to find that I’d mistakenly placed it in the freezer. Thankfully, it was still functional or I would have had to pay a few hundred dollars for a new one.

When testing PCB prototypes, I sometimes went on an entirely different hunt to find short circuits amongst hundreds of traces and components in my PCB designs. It wasn’t a pleasant affair, although I’ve learned what the common spots are for such occurrences.

Signs of a Short Circuit

How do you know if you have short circuits on a PCB? Depending on where it may be shorted, you may have various symptoms. For example, you might have a sudden ‘pop’ followed by arcing and a broken trace when you power on the PCB. Such dramatic signs often point to short circuits occurring on power traces.

Sometimes the signs are more subtle, and you don’t realize until you’re testing specific functionalities of the circuit. Two input pins that are shorted with each other will provide no hints during a test power up. You’ll only realize that the circuit isn’t functioning as it is meant to when the inputs don’t return the right reading. 

In some cases, short circuits don’t cause obvious damage, but they are still easy to pick up. An LED’s positive lead shorted to ground will prevent the LED from lighting up. Short circuits that affect visual, audio, or mechanical outputs are often also easier to spot.

Tips for Locating Short Circuits 

a digital multimeter with attached probes

A multimeter helps to detect short circuits.

Once you have a hunch that there are shorts in your circuit, you need to move on to the hard part--locating them. You’ll need common sense, sound electronics knowledge (like Ohm’s Law), sharp eyes, and tools to find the shorts.

Visually Scan the PCB

Sometimes, you can pick up obvious shorts like a solder joint between pins or copper areas that are not fully etched out. You may want to use a magnifying glass as some of the shorts are as thin as a hair. 

Look for Signs of Burnt Components

A short circuit may result in some components getting burnt. A cracked IC, blown capacitor, or the familiar acrid smell of burnt components are all telltale signs that a short circuit is close by. Locate and remove the damaged component and investigate traces connected to it. 

You’ll either find the fault on the damaged component or the traces linked to it.

Probe with a Multimeter

The multimeter will be your best pal in spotting a short circuit. Check for the continuity of different traces that you suspect are shorted. While it doesn’t pinpoint the exact location of the short, it gives you an idea of where to start looking.

Use a Thermal Camera

A thermal camera, which uses infrared technology, can be helpful in determining the exact locations of the short. Assuming that you’ve powered up the board, the short circuit may conduct an excessive amount of current and heat up.

You can use the thermal camera to pick up the hotspots and then verify it with a visual inspection. However, if the short occurs in the inner layers, manual inspection will be impossible. 

Destructive Testing

Short circuits between power and ground are the toughest to find. There are so many possibilities, particularly if you have a large area of ground or power planes

In such circumstances, you’ll have no option but to try cutting some of the traces to isolate part of the circuit. The reason for doing so is not only to locate the short circuit but also to learn if it’s a design or manufacturing mistake. 

What Causes Short Circuits on a PCB

a gloved hand inspecting a printed circuit board

Mistakes in PCB design, fabrication, and bad components can cause short circuits

You’ll want to take every precaution to prevent short circuits on your PCB, and this means getting down to the root causes. Some short circuits are created during manufacturing or assembly. When a thin line of copper remains during fabrication, a hairline short is formed.

Short circuits may also happen during reflow soldering. The solder paste may accidentally connect two pins that are very close to each other. In some cases, mistakes are made during PCB design where traces between different nets are accidentally connected.

Sometimes, the short doesn’t occur on the PCB but is instead due to faulty components. Removing the faulty component will solve the issue. 

While manufacturing and assembly are somewhat beyond your control, you can reduce short circuits resulting from design mistakes by using the right PCB design and analysis software. Use OrCAD PCB Designer and its DRC feature to detect short circuits in your nets before finalizing the design.

If you’re looking to learn more about how Cadence has the solution for you, talk to us and our team of experts

About the Author

Cadence PCB solutions is a complete front to back design tool to enable fast and efficient product creation. Cadence enables users accurately shorten design cycles to hand off to manufacturing through modern, IPC-2581 industry standard.

Follow on Linkedin Visit Website More Content by Cadence PCB Solutions
Previous Article
Vias: Types and Applications
Vias: Types and Applications

This article discusses the types and applications of vias in printed circuit board design and how PCB desig...

Next Article
How to Optimize PCB Design for SMT Assembly Process Flow
How to Optimize PCB Design for SMT Assembly Process Flow

SMT assembly process flow is a critical part of PCB production. Using the right design tools can help ensur...

×

10 Common DFM Issues and How to Fix Them

First Name
Last Name
Location
State
Opt-in to future emails and I understand I can unsubscribe at any time.
I agree to the terms of use*
*required
Terms of Use
Thank you!
Error - something went wrong!