Cadence System Analysis

Solving electromagnetic, electronics, thermal, and electromechanical simulation challenges to ensure your system works under wide-ranging operating conditions

  • Using PCB Thermal Simulation in the Pre-Development Design Phase

    Using PCB Thermal Simulation in the Pre-Development Design Phase

    The impact of heat on PCB performance, reliability, and efficiency is significant, making it necessary to run PCB thermal simulations of design layouts to ensure electronic product designs are optimiz

    Read Article
  •  Shorten Design Cycle Time Using 3D EM Simulation Software

    Shorten Design Cycle Time Using 3D EM Simulation Software

    Before physical prototyping, model, analyze, and optimize EM designs with 3D EM simulation software.

    Read Article
  •  EFT Testing for Electronic Systems

    EFT Testing for Electronic Systems

    To check whether an electronic system is immune to EFTs, routine EFT testing must be conducted. Read on to understand how to conduct EFT testing and why it is so important.

    Read Article
  • Filter Technologies for 5G Wireless Communication Systems

    Filter Technologies for 5G Wireless Communication Systems

    RF Filter design and especially 5g RF filters in wireless communication systems are facing stress from MIMO technologies, EM analysis is a necessity.

    Read Flipbook
  • 5G Communications

    5G Communications

    Designing tried-and-true 5g technologies, or new applications of mmWave 5g systems demands accurate and strong tools. 5g mmWave antenna design stops for nobody!

    Read Flipbook
  • RFIC PA Development for Communication and Radar Systems

    RFIC PA Development for Communication and Radar Systems

    An RFIC Power amplifier (PA) based on GaS or GaAn technologies can be hard to design, so too can added CMOS or SiC technologies increase difficulty.

    Read Flipbook
  • Applying the Optimal Power Flow Model to Your PDN

    Applying the Optimal Power Flow Model to Your PDN

    Optimal power flow is a cost minimization model that can be applied to high-level PDN design.

    Read Article
  • Improve Product Design with Accelerated Life Testing Thermal Cycling

    Improve Product Design with Accelerated Life Testing Thermal Cycling

    Accelerated life testing thermal cycling quantifies the life characteristics, failures, and defects that occur when products are employed in the field.

    Read Article
  • Heat Transfer Simulator for Analyzing Thermal Effects

    Heat Transfer Simulator for Analyzing Thermal Effects

    In electronic circuit systems, heat transfer negatively impacts performance. The investigation of heat transfer using simulation is helpful to design effective thermal management.

    Read Article
  • Power System Interharmonics Show That No Power System Is Perfect

    Power System Interharmonics Show That No Power System Is Perfect

    Power system interharmonics need to be filtered or suppressed in your AC system. Here’s how you can produce clean AC input power for your products.

    Read Article
  • Incorporate a Power Management System for Reliable and Stable Electrical Power Supply

    Incorporate a Power Management System for Reliable and Stable Electrical Power Supply

    Achieve a reliable and stable power supply in industrial and commercial electrical networks with a power management system.

    Read Article
  • How PDN Transient Current Dynamics Affect DC Power

    How PDN Transient Current Dynamics Affect DC Power

    The PDN transient current dynamics affect DC power from ground and supply rails.

    Read Article
  • Improve Power Factor and Efficiency Using Bridgeless Power Factor Correction Rectifiers

    Improve Power Factor and Efficiency Using Bridgeless Power Factor Correction Rectifiers

    Replace diode bridge rectifiers using bridgeless PFC rectifiers to improve power factor and efficiency.

    Read Article
  • Clamp Diodes and Transient Voltage Protection in Circuit Boards

    Clamp Diodes and Transient Voltage Protection in Circuit Boards

    Clamp diodes, or diodes in clamping circuits, are installed to help guard circuits from transient voltage.

    Read Article
  • Innovations in Wideband RF Signal Processing

    Innovations in Wideband RF Signal Processing

    Wideband (WB) RF signal processing provides industry-standard performance and enables Giga Samples Per Second (GSPS) data transfer rate, zero loss, good quality, and high-performance in systems.

    Read Article
  •  RF Antenna Design and Layout Tips for Your PCB

    RF Antenna Design and Layout Tips for Your PCB

    RF antenna designers should take a cue from mixed-signal designers when creating a PCB layout—read on for tips to ensure signal integrity in your RF design.

    Read Article
  • Which Design Choices can Reduce EMF Noise?

    Which Design Choices can Reduce EMF Noise?

    EMF noise can be reduced with some smart layout decisions. Here’s how you can take control over EMF noise in your design.

    Read Article
  • Optimal and Cost-Effective Machine Design Using FEM Magnetic Simulation

    Optimal and Cost-Effective Machine Design Using FEM Magnetic Simulation

    FEM magnetic simulation is a powerful simulation tool to achieve optimal and cost-effective machine design.

    Read Article
  • Getting Started with Robust Finite Element Method and Solvers

    Getting Started with Robust Finite Element Method and Solvers

    An introduction on the topic of FEM solvers—the different types, uses, and applications.

    Read Article
  •  The Basics of Steady-State Heat Transfer Analysis

    The Basics of Steady-State Heat Transfer Analysis

    Even in the steady-state, heat still moves between hot and cold regions. Here’s how you can use a field solver for steady-state heat transfer analysis.

    Read Article
  • loading
    Loading More...